Old house renovation is a common type of home decoration project. It can improve the original living environment to the greatest extent and give the home a brand new look. However, most people are worried about the various subsequent impacts caused by secondary renovation, such as long demolition construction period, high cost, loud noise, etc., and often do not know how to start.
Today, the editor recommends to you a renovation technique that does not require dismantling and has a faster construction period - the secondary renovation process of thin plates. On the basis of ensuring the flatness of the original base layer, light thin plates and rock layers are directly laid on the surface of the original base layer. Board, quickly achieve freedom of renovation.
In order to let everyone better understand the entire second renovation process, LA'BOBO's exhibition hall has been completely upgraded. In just 3 days, the 26m² children's room was transformed into a modern and simple style studio that is half leisure and half office. I hope you will finish reading this This case introduction can help everyone, let’s take a look at how it transformed!
✦Before
Before renovation - children's room
The original children's room had many colors and the overall style was cartoonish, making it unsuitable for office use. In addition, the middle wall structure design divides the area into two, and the apartment layout is not open and clear enough, which is not conducive to daily reception.
Before renovation - children's room
Design strategy:
1. There are no partitions in the overall space to create as many possibilities for interaction as possible.
2. The studio must be compatible with the reception and negotiation area and the office area to meet different functional needs.
3. Install a gate at the entrance to increase the privacy of the space..
4. The overall style is mainly modern and simple, using simple and neat lines, with black, white and gray as the main colors.
After renovation - office
After determining the basic tone and plan of the space, let’s take a look at the specific renovation process!
1 Ground renovation
The ground renovation
After the original partition walls of the space are dismantled, the floor needs to be cleaned, and the flatness and hollowness of the floor need to be tested to ensure that the flatness of the base layer meets the requirements of the secondary renovation process of thin plates.
Apply ceramic tile adhesive on the surface of the original base layer to enhance the bonding between the thin plate and the base layer.
Mix water and tile adhesive dry powder in proportion, and use an electric mixer at low speed to mix well until it becomes a paste.
Using the thin wet pasting process, apply tile adhesive evenly on the surface of the original base layer and the back of the thin plate, sort out uninterrupted zigzag stripes with parallel and consistent textures, and use a tiler to eliminate excess air gaps and gaps generated during the paving process. Bubbles so that they fit tightly on both sides.
When laying adjacent tiles, it is necessary to reserve appropriate gaps, insert levelers and pressure strips to level the tiles to ensure consistent flatness of the board surface. After the paving is completed, wait for 24 hours before knocking off the leveler from the side and finishing the seam and edge processing.
2 Wall renovation
Metope renovation
After completing the ground protection work, appropriate grid lines can be popped up on the original wall according to the design requirements and sheet specifications, and the wall opening positions can be reserved.
After measuring the size and position of the opening, mark and position it on the surface of the sheet, and use a cutting knife to cut square holes of corresponding sizes at the corresponding positions on the surface of the sheet.
After confirming that the position of the opening is correct, apply the evenly mixed adhesive on the back of the sheet in sections and at fixed points using the spot-gluing method, and lay it on the wall according to the grid lines.
When paving adjacent sheets, attention should be paid to using the same processing method as the ground leveling, and finally the seams and edges should be done well.
Due to the large area of the wall, the wall renovation and paving took a total of two days, which was longer than the floor renovation. The overall space renovation took a total of three days. Next, let’s take a look at the transformed space~
—— After renovation——
The wall is made of PR24 castle gray 800x1400x6mm (glossy surface)
The ground is made of PR03 Tenier gray (light gray) 800x1400x6mm (bright surface)
The light gray texture is as silky as mist, agile and ethereal, adding a hazy and luxurious beauty to the space.
The studio does not have too many decorations, less is more, giving enough white space to leave more possibilities for follow-up actions.
As an extension of the space for leisure, the sofa is also a venue for receiving important customers. The color combination of light and dark is chosen to make the overall space more impactful.
The dark gray product storage cabinet is paired with a simple and elegant desk, which facilitates easy access to products during the communication process, making the entire negotiation process smoother.
Using thin plates for secondary renovation, there is no need to dismantle them, they can be laid directly, which takes less time. The thickness is only increased by 1cm before and after renovation, basically does not take up space, and it also achieves high hardness, wear resistance, low water absorption, It has good toughness and other characteristics, and its performance is even better than traditional ceramic tiles. It can be used indoors and outdoors, making it the best choice for renovating old houses!
After reading this renovation case introduction, do you know how to choose the second space renovation and reinstallation?
(Some pictures come from the Internet, if there is any infringement, please contact us to delete)
